eLibrary >
ISO Guide 78:2012 Safety of machinery - Rules for drafting and presentation of safety standards >
ISO Guide 78:2012 Safety of machinery - Rules for drafting and presentation of safety standards, 2012
- Section sec_1
- Section sec_2
- Section sec_3
- Figure fig_1
- Section sec_4
- Section sec_4.1
- Section sec_4.2
- Section sec_4.3
- Section sec_4.3.1
- Section sec_4.3.2
- Section sec_4.3.3
- Section sec_4.4
- Section sec_4.5
- Section sec_5
- Section sec_5.1
- Section sec_5.2
- Section sec_5.3
- Section sec_5.4
- Section sec_5.5
- Section sec_5.5.1
- Section sec_5.5.2
- Section sec_5.6
- Section sec_5.7
- Section sec_5.8
- Section sec_6
- Section sec_6.1
- Section sec_6.2
- Section sec_6.3
- Section sec_6.3.1
- Section sec_6.3.2
- Section sec_6.3.3
- Section sec_6.4
- Section sec_6.4.1
- Section sec_6.4.2
- Section sec_6.5
- Section sec_6.6
- Section sec_6.6.1
- Section sec_6.6.2
- Section sec_6.6.3
- Section sec_6.6.4
- Section sec_6.7
- Section sec_6.7.1
- Section sec_6.7.2
- Section sec_6.7.3
- Section sec_6.7.4
- Section sec_6.7.5
- Section sec_6.7.6
- Section sec_6.8
- Section sec_6.8.1
- Section sec_6.8.2
- Section sec_6.9
- Section sec_6.9.1
- Section sec_6.9.2
- Section sec_6.9.3
- Section sec_6.9.3.1
- Section sec_6.9.3.2
- Section sec_6.9.3.3
- Section sec_6.9.4
- Section sec_6.10
- Section sec_6.10.1
- Section sec_6.10.2
- Section sec_6.10.2.1
- Section sec_6.10.2.2
- Section sec_6.10.2.3
- Section sec_6.10.3
- Annex sec_A
- Annex sec_B
- Reference ref_1
- Reference ref_2
- Reference ref_3
- Reference ref_4
- Reference ref_5
- Reference ref_6
- Foreword
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 General principles
- 4.1 All safety standards
- 4.2 Type-B standards
- 4.3 Type-C standards
- 4.4 Need for a type-B standard
- 4.5 Deviations in a type-C standard
- 5 Principles to be considered before and during drafting process
- 5.1 General
- 5.2 Determination of necessity for standardization and/or revision
- 5.3 Definition of scope
- 5.4 Identification of hazards, hazardous situations or hazardous events
- 5.5 Estimation and evaluation of risk(s) generated by hazard(s)
- 5.6 Identification of risk reduction objectives
- 5.7 Determination of safety requirements and/or protective/risk reduction measures for eliminating hazards and/or limiting risks
- 5.8 Verification of compliance with safety requirements and/or protective/risk reduction measures
- 6 Format of a safety standard
- 6.1 General
- 6.2 Foreword
- 6.3 Introduction
- 6.4 Scope
- 6.5 Normative references
- 6.6 Terms and definitions [symbols and abbreviated terms]
- 6.7 Safety requirements and/or protective/risk reduction measures
- 6.8 Verification of the safety requirements and/or protective/risk reduction measures
- 6.9 Information for use
- 6.10 Annexes
- Annex A (normative) Procedure to be followed if type-B standards do not exist
- Annex B (informative) Model format of a type-C International Standard
- Bibliography [Go to Page]