|
EDITION
PUBLISHER
CONTENT TYPE
Act
Admin Code
Announcements
Bill
Book
CADD File
CAN
CEU
Charter
Checklist
City Code
Code
Commentary
Comprehensive Plan
Conference Paper
County Code
Course
DHS Documents
Document
Errata
Executive Regulation
Federal Guideline
Firm Content
Guideline
Handbook
Interpretation
Journal
Land Use and Development
Law
Legislative Rule
Local Amendment
Local Code
Local Document
Local Regulation
Local Standards
Manual
Model Code
Model Standard
Notice
Ordinance
Other
Paperback
PASS
Periodicals
PIN
Plan
Policy
Product
Product - Data Sheet
Program
Provisions
Requirements
Revisions
Rules & Regulations
Standards
State Amendment
State Code
State Manual
State Plan
State Standards
Statute
Study Guide
Supplement
Sustainability
Technical Bulletin
All
|
Description of ASTM-D6485 2018ASTM D6485-18Withdrawn Standard: Standard Guide for Risk Characterization of Acute and Irritant Effects of Short-Term Exposure to Volatile Organic Chemicals Emitted from Bedding Sets (Withdrawn 2024)ASTM D6485Scope 1.1 This guide describes procedures for conducting risk characterization of exposure to volatile organic chemicals (VOCs) emitted from bedding sets or an ensemble of a mattress and supporting box spring. 1.2 This guide is for risk characterization of short-term exposures to a new bedding set brought into a residential indoor environment. The risk characterization considerations presented in this guide are applicable to both the general population and sensitive subgroups, such as convalescing adults. 1.3 The risk characterization addressed in this guide is limited to acute health and irritation effects resulting from short-term exposure to VOCs in indoor air. Although certain procedures described in this guide may be applicable to assessing long-term exposure, the guide is not intended to address cancer and other chronic health effects. 1.4 VOC emissions from bedding sets, as in the case of other household furnishings, usually are highest when the products are new. A used bedding set may also emit VOCs, either from the original materials or as a result of its use. The procedures presented in this guide also are applicable to used bedding sets. 1.5 Risk characterization procedures described in this guide should be carried out under the supervision of a qualified toxicologist or risk assessment specialist, or both. 1.6 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard. 1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use. 1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee. Keywords acute toxicity; air concentration; emissions; exposure assessment; hazard assessment; health effect; inhalation; irritant effect; odor characterization; odor threshold; risk characterization; ICS Code ICS Number Code 13.120 (Domestic safety) DOI: 10.1520/D6485-18 The following editions for this book are also available...This book also exists in the following packages...Subscription InformationMADCAD.com ASTM Standards subscriptions are annual and access is unlimited concurrency based (number of people that can access the subscription at any given time) from single office location. For pricing on multiple office location ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
Some features of MADCAD.com ASTM Standards Subscriptions are: - Immediate Access: As soon as the transaction is completed, your ASTM Standards Subscription will be ready for access.
For any further information on MADCAD.com ASTM Standards Subscriptions, please contact us at info@madcad.com or +1 800.798.9296.
About ASTMASTM International, formerly known as the American Society for Testing and Materials (ASTM), is a globally recognized leader in the development and delivery of international voluntary consensus standards. Today, some 12,000 ASTM standards are used around the world to improve product quality, enhance safety, facilitate market access and trade, and build consumer confidence. ASTM’s leadership in international standards development is driven by the contributions of its members: more than 30,000 of the world’s top technical experts and business professionals representing 150 countries. Working in an open and transparent process and using ASTM’s advanced electronic infrastructure, ASTM members deliver the test methods, specifications, guides, and practices that support industries and governments worldwide. |
GROUPS
|
|
MADCAD.com
by Compu-tecture, Inc.
|
Contact Us
3000 Connecticut Ave, NW
Suite 200
Washington, DC 20008
+1 800.798.9296
+1 202.265.1940
|
|
Partnerships
|