eLibrary >
BS EN 10088-2:2014 Stainless steels - Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes >
BS EN 10088-2:2014 Stainless steels - Technical delivery conditions for sheet/plate and strip of corrosion resisting steels for general purposes, 2014
- Foreword
- Introduction
- 1 Scope
- 2 Normative references
- 3 Terms and definitions
- 4 Designation and ordering [Go to Page]
- 5 Classification of grades
- 6 Requirements [Go to Page]
- 7 Inspection and testing [Go to Page]
- 8 Marking
- Table 1 — Chemical composition (cast analysis) of austenitic corrosion resisting steels
- Table 2 — Chemical composition (cast analysis) of austenitic-ferritic corrosion resisting steels
- Table 3 — Chemical composition (cast analysis) of ferritic corrosion resisting steels
- Table 4 — Chemical composition (cast analysis) of martensitic and precipitation hardening corrosion resisting steels
- Table 5 — Permissible product analysis tolerances on the limiting values given in Tables 1 to 4 for the cast analysis
- Table 6 — Type of process route and surface finish of sheet, plate and stripa
- Table 7 — Mechanical properties at room temperature of austenitic steels in the solution annealed condition a (see Table A.1) and resistance to intergranular corrosion
- Table 8 — Mechanical properties at room temperature of austenitic-ferritic steels in the solution annealed condition (see Table A.2) and resistance to intergranular corrosion
- Table 9 — Mechanical properties at room temperature of ferritic steels in the annealed condition (see Table A.3) and resistance to intergranular corrosion
- Table 10 — Mechanical properties at room temperature of martensitic steels in the heat-treated condition (see Table A.4)
- Table 11 — Mechanical properties at room temperature of precipitation hardening steels in the heat treated condition (see Table A.5)
- Table 12 — Minimum values for the 0,2 %-and 1 %-proof strength of austenitic steels at elevated temperatures
- Table 13 — Minimum values for the 0,2 %-proof strength of austenitic-ferritic steels at elevated temperatures
- Table 14 — Minimum values for the 0,2 % proof strength of ferritic steels at elevated temperatures
- Table 15 — Minimum values for the 0,2 % proof strength of martensitic steels at elevated temperatures
- Table 16 — Minimum values for the 0,2 % proof strength of precipitation hardening steels at elevated temperatures
- Table 17 — Tensile strength levels in the cold worked condition (process route 2H)
- Table 18 — 0,2 %-proof strength levels in the cold worked condition (process route 2H)
- Table 19 — Available tensile strength levels of steel grades in the cold worked condition (process route 2H)
- Table 20 — Available 0,2 %-proof strength levels of steel grades in the cold worked condition (process route 2H)
- Table 21 — Tests to be carried out, test units and extent of testing in specific testing
- Table 22 — Marking of the products
- Figure 2 — Direction of bending the test piece in relation to the rolling direction in the resistance to intergranular corrosion test
- Annex A (informative) Guidelines for further treatment (including heat treatment) in fabrication
- Table A.1 — Guidelines on the temperatures for hot forming and heat treatmenta of austenitic corrosion resisting steels
- Table A.2 — Guidelines on the temperatures for hot forming and heat treatmenta of austenitic-ferritic corrosion resisting steels
- Table A.3 — Guidelines on the temperatures for hot forming and heat treatmenta of ferritic corrosion resisting steels
- Table A.4 — Guidelines on the temperatures for hot forming and heat treatment a of martensitic corrosion resisting steels
- Table A.5 — Guidelines on the temperatures for hot forming and heat treatment a of precipitation hardening corrosion resisting steels
- Annex B (informative) Applicable dimensional standards
- Bibliography [Go to Page]